View DS1640C_276339.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DS1640/DS1640C Personal Computer Power FET
www.dalsemi.com
FEATURES
Contains four P channel power FET switches that can each supply over 300 mA @ 0.2 volts drop Controlled directly from CMOS or TTL level signals Fast switching time of less than 10 s at rated supply current 16-pin DIP or 16-pin SOIC surface mount package Positive logic signal turns each FET on and ground or low level signal turns each FET off Off condition allows less than 50 nA of current flow Low control gate capacitance of less than 5 pF FET gates can either follow inputs or be latched Designed for use with power supplies ranging from +3 to +5 volts
PIN ASSIGNMENT
IN1 GATE1 OUT1 LATCH GND OUT2 GATE2 IN2 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 IN4 GATE4 OUT4 NC VCC OUT3 GATE3 IN3
16-Pin DIP (300-mil) See Mech. Drawings Section
IN1 GATE1 OUT1 LATCH GND OUT2 GATE2 IN2 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 IN4 GATE4 OUT4 NC VCC OUT3 GATE3 IN3
16-Pin DIP SOIC (300-mil) See Mech. Drawings Section
PIN DESCRIPTION
VCC GND IN1-IN4 OUT1-OUT4 GATE1-GATE4 NC LATCH - +3 to +5 Volt Input - Ground - FET Sources - FET Drains - FET Control Gates - No Connection - Gate Inputs Latch Control
DESCRIPTION
The DS1640 contains four P channel power MOS FETs designed as switches to conserve power in personal computer systems. When connected to power management control units, power consuming devices like disk drives or display panel backlights can be routinely shut down to conserve battery or main power supply energy. The P channel power MOS FETs are individually controlled and are capable of handling 300 mA each continuously with less than 0.2 volts drop from input to output. The device requires a +3 U +5 volt power supply input which is used to power internal logic and to operate a gate bias generator.
1 of 4
111999
DS1640/DS1640C
OPERATION
With +3 U +5 volts applied between the VCC pin and ground, any one of four inputs can be connected or disconnected from its respective output based on the bias applied to the control gate (see Figure 1). A set of four internal latches is controlled by the latch input. The logic levels passed to the FET gates are controlled by the gate inputs and latch pin status. When the latch pin is logic 0, the gate input levels are inverted and passed directly to the control gates, enabling the switches to be switched both independently and asynchronously. With a transition from logic 0 to logic 1 on the latch pin, the input levels present on the gate inputs are locked by the four internal latches, maintaining the corresponding FET gates at those levels. As long as the latch input is maintained at logic 1, the FET gate levels are maintained. When the latch input is returned to logic 0, the gate inputs again are inverted and passed to the FET control gates without being latched. A TTL or CMOS logic 1 turns a switch completely on and TTL or CMOS logic 0 turns a switch completely off. The four switches can be operated independently or two or more can be connected in parallel for added current carrying capability. The four switches contained within the DS1640 are not designed to be operated in a linear manner. When VCC is not applied to the DS1640 or if VCC is not within nominal limits, the output levels and current carrying capability of the four switches are not guaranteed. When all four gate inputs are off (logic 0) the device enters a low VCC current standby mode because the onboard charge pump is turned off. The gate and latch inputs are CMOS-compatible throughout the entire VCC range and are TTL-compatible when VCC falls between 4.5 and 5.5V.
DS1640 BLOCK DIAGRAM Figure 1
2 of 4
DS1640/DS1640C
ABSOLUTE MAXIMUM RATINGS*
Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -0.3V to +7.0V 0C to 70C -55C to +125C 260C for 10 seconds
* This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability.
DC OPERATING CONDITIONS
PARAMETER Supply Voltage Logic 0 Input 3.0 V < VCC < 4.5 V Logic 0 Input 4.5 V < VCC < 5.0 V Logic 1 Input 3.0 V < VCC < 5.0 V Source Voltage SYMBOL VCC VIL2 VIL1 VIH VSOURCE MIN 3.0 -0.3 -0.3 2.0 TYP MAX 5.5 +0.5 +0.8 VCC +0.5 VCC +0.5
(0C to 70C)
UNITS V V V V V NOTES 1, 2 1 1, 7 1, 7
DC ELECTRICAL CHARACTERISTICS
PARAMETER Supply Current Supply Current Switch Off Leakage Switch On Resistance Switch Current @ VF = 200 mV Input Leakage Gate Input Capacitance SYMBOL ICC1 ICC2 ISL RON IS IIL CG MIN
(0C to 70C; VCC = +5V + 10%)
TYP 0.3 0.1 0.3 MAX 1 1 100 0.67 300 +1 5 UNITS mA A nA mA A pF NOTES 3 4
5 6 7
-1
DC ELECTRICAL CHARACTERISTICS
PARAMETER Switching Time (OFF ON) Switching Time (ON OFF) Minimum Time to Engage Latch SYMBOL tSTON tSTOFF tLM MIN
(0C to 70C; VCC = +5V + 10%)
TYP MAX 10 10 50 UNITS s s ns NOTES
3 of 4
DS1640/DS1640C
NOTES:
1. All voltages are referenced to ground. 2. When VCC is below minimum limits output levels are not guaranteed. 3. ICC1 is the supply current with one or more switches on. 4. ICC2 is when all switches are off and all inputs are within 0.5V of a supply rail. 5. Each switch is capable of carrying 300 mA maximum at 200 mV forward drop. 6. Input leakage applies to the four gate inputs and the latch input only. 7. Applies to each of four gate inputs and the latch input. Dallas Semiconductor devices are built to the highest quality standards and manufactured for long term reliability. All DS1640 devices are made using the same quality materials and manufacturing methods. However, consumer versions of the DS1640 are not exposed to environmental stresses that some commercial device manufacturing flows require. Devices that are designated as consumer product have a "C" designator in the product number. For example, the DS1640C is a consumer grade product.
4 of 4

▲Up To Search▲

Price & Availability of DS1640C

	To Download DS1640C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .